After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. We highly recommend that the kits not be broken down unless suitable weighing equipment isĪvailable. Standard packages are in pre-measured kits and should be mixed as supplied in the kit. Plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbanding.ģ) PRODUCT MIXING: This product has a mix ratio of 9.0# part A to 4.15# part B. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating.
Eximo concrete cleaner use temperature free#
All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate.Ī test should be made to determine that the concrete is dry this can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. Low temperatures or temperature fluctuations may cause crystallization.Ģ) SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast) to remove all laitance and provide a suitable profile. Continuous storage should be between 60 and 90 degree F. MIXING AND APPLICATION INSTRUCTIONS (#3137MUV)ġ) PRODUCT STORAGE: Store product in an area so as to bring the material to normal room temperature before using. See reverse side for limitations of our liability and warranty. Physical properties are typical values and not specifications. Apply a suitable primer before using this product See reverse side for application instructions. All new concrete must be cured for at least 30 days prior to application. For best results, apply with a ¼” nap roller. Substrate temperature must be 5☏ above dew point. Clear aliphatic urethane topcoats can further This product is not UV color stable but has very good UV resistance for an epoxy product. Therefore, use only product from the same batch for an entire job. #3137MUV in aggregate filled systems, with or without a clear urethane topcoat.Ĭolor stability or gloss may be affected by environmental conditions such as high humidity, chemical exposure, UV exposure or exposure to lighting such as sodium vapor lights.Ĭolors may vary from batch to batch. TOPCOAT: Optional – #3321/#3322 aliphatic urethanes or successive coats of PRIMER: Recommended #3015 clear, #3154 clear NOTE: extensiveĬhemical resistance information is available through your sales representative. Splash spill, D - 72 hour immersion, E - long term immersion. Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term GARDNER VARIABLE IMPACTOR: 50 inch pounds direct – passed Part B “CORROSIVE LIQUID N.O.S., 8, UNI1760, PGIII” VISCOSITY: Mixed = 700-1000 cps (typical) MIX RATIO 9.0 pounds part A (.99 gallons) to 4.15 pounds part B (.49 gallons) (volumes approx.)įINISH CHARACTERISTICS: Gloss (60 to 90 60 degrees Erichsen glossmeter)ĪBRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles = 36 mg lossĬOMPRESSIVE STRENGTH: 11,200 psi ASTM D695ĪDHESION: 350 psi elcometer (concrete failure, no delamination) STANDARD COLORS: Clear – gardner color 1-2ĬOVERAGE PER GALLON: 90-100 square feet per gallon 16-18 milsģ gallon kits (2.95 gallons net approximately)ġ5 gallon kits (14.75 gallons net approximately)
VOLATILE ORGANIC CONTENT: Nearly zero pounds per gallon Super Dye (Acetone Dye Concentrate for Interior Concrete)ĩ0-100 square feet per gallon 16-18 mils wet film thickness.Super Color (UV Stable Semi-Transparent Concrete Stain).
V-SCRUB ETCH (Acidic Cleaner for Reacted Stains & Etching).V-SCRUB HD (Heavy Duty Concentrated Alkaline Cleaner).
Eximo concrete cleaner use temperature pro#
ATG CounterTek CTS Pro - for Concrete, Terazzo, & Stone.Industra-Coat 3521 (Water Based, Gloss, Urethane Topcoat).Industra-Coat 3520 (Water Based, Low Gloss, Urethane Topcoat).Industra-Coat 3322 (Low VOC Urethane Topcoat, High Gloss).Industra-Coat 3321 (Urethane Topcoat, High Gloss).Industra-Coat Epoxy & Urethane Complete Kit - Satin/Matte.Industra-Coat Epoxy & Urethane Complete Kit - Gloss.Industra-Seal 117 PLS (Professional Strength Lithium Silicate).PHASE II (Repellent Enhancer and Hardener/Densifier).
0 kommentar(er)
